24093_ADP 303 Eng. 27/02/1998 10:34 Side 8
Installation & Setup
7
Large: Set the switch to this positionSmall: Set the switch to this position1. Using the remote control or front
when using traditional full rangewhen using a smaller bookshelf orpanel controls appropriate to your
loudspeakers that are capable ofOsatellite� center speaker that has limitedreceiver, processor or pre-amp, make
handling sounds below 100 Hz. In thislow frequency range and is unable tonote of the delay time setting you use for
position, the output to the surroundreproduce sounds below 100 Hz. Whennormal surround listening.
output jacks is full range. the switch is in the OSmall� position, LFE
2. Press the front panel DELAY o button
Center audio will be routed to the
None: Set the switch to this positionuntil the delay time indicator illuminates
Subwoofer output, provided that the
when no surround speakers areto show a setting that is closest to that
Subwoofer Speaker Mode Switch ? is in
connected. In this position the full rangeused with your conventional surround
the OON� position. Otherwise itOs routed
surround audio that would otherwise besystem.
to the front speakers.
routed to the surround channels will be
SYSTEM CONNECTIONS
mixed in with the FRONT LEFT and4) Subwoofer Mode
FRONT RIGHT audio. Set this switch to determine the routingThe ADP303 may be used in one of three
of low frequency sounds for all channels.operating modes, depending on the other
Small: Set the switch to this position
The factory default setting is OON�, toequipment in your system. Before
when using smaller bookshelf or
indicate that a subwoofer is present.proceeding to the final adjustments,
Osatellite� speakers that have limited low
check to make certain that the ADP303 is
frequency range and are unable toOn: Select this position if the ADP303 is
connected to the components in your
reproduce sounds below 100 Hz. Whenconnected to an amplifier or Receiver
system based on one of the three options
the switch is in the OSmall� position allequipped with a Subwoofer INPUT
shown on the following pages. Note that
sounds below 100 Hz will be routed to theterminal, or if it is directly connected to a
proper system calibration and operation
Subwoofer output jack. When thepowered subwoofer.
are dependent on making the right
Subwoofer Speaker Mode switch ? is in
Off: Select this position if a Subwooferconnections and use of the controls as
the OON� position, LFE surround audio
will not be used. outlined on each page.
will be routed to the subwoofer. When the
Subwoofer Speaker Mode Switch ? is inIn this position the low frequency soundsIf you will be using the ADP303 in
the OOFF� position, LFE surround audio(below 100 Hz) will be routed to theconjunction with an AVR80, AVI250 or
will be routed to the front left/rightFRONT LEFT, RIGHT and/or CENTERother AV receiver equipped with direct
speakers.terminals, depending on the setting ofinputs for a O6 Channel Direct�
the speaker switches for those channels. connection via RCA jacks, use the system
3) Center Speakers Mode
configuration shown on page 8.
This switch determines the frequency5) System Reset
range for the center channel speaker.Once you have completed any changes toIf you will be using the ADP303 in
Select Large, None or Small dependingthe Speaker Selection Switches turn theconjunction with an external preamp or
on the type of center channel speakerADP303 off, and then on again to entersurround sound processor, use the system
installed. The factory default setting isthe settings into the unitOs memory forconfiguration shown on page 9.
OSmall�.future use.
If you will be using the ADP303 in
Large: Set the switch to this positionconjunction with an AV receiver equipped
DELAY TIME ADJUSTMENT
when using traditional full range loud-with Opre-out/main-in� jacks for all five
speakers that are capable of handlingaudio channels, use the systemDelay time adjustment enables you to
adjust the timing between signals at the
sounds below 100 Hz.configuration shown on page 10.
front and rear channels. Since the use of
None: Set the switch to this positionthe ADP303 may bypass the delay settings
when a center channel speaker is notin your receiver or preamp it is important
connected. Full range audio signals thatto establish a proper delay setting for use
would otherwise be routed to the centerin 6 channel operation.
channel will be mixed in with the
FRONT LEFT and FRONT RIGHT audio. |
ACEC
